Державне підприємство «Український науково-дослідний і навчальний центр проблем стандартизації, сертифікації та якості» (ДП «УкрНДНЦ»)
Наказ від 14.06.2018 № 165
EN ISO 16093:2017
Machine tools — Safety — Sawing machines for cold metal (iSo 16093:2017)
прийнято як національний стандарт методом підтвердження за позначенням
ДСТУ EN ISO 16093:2018
(EN ISO 16093:2017, IDT; ISO 16093:2017, IDT)
Верстати. Безпечність. Верстати розпилювальні для холодного різання металу
English Version
Machine tools — Safety — Sawing machines for cold metal
1 Scope
This document deals with all significant hazards, hazardous situations and events to sawing machines
as defined in Clause 3, whose prim ary intended use is for sawing cold metal (ferrous and non-ferrous),
or material partly of cold metal and under conditions of misuse which are reasonably foreseeable by
the manufacturer (see Clause 4).
This document is applicable to (metal) sawing machines which are manufactured after the date of
publication of this document.
When additional processing (i.e. m illing, boring, marking, finishing operation, etc.) is considered, this
document can serve as a basis for safety requirements. For more detailed information, refer to the
bibliography.
This document deals with noise hazards but does not provide a full noise test code. It is intended to
draft such a code in the next revision of this document.
This document does not include requirements and safety measures for fire and explosion hazards. It is
intended to deal w ith them in the next revision of this document.
2 Normative references
The following documents are referred to in the text in such a w ay that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 683-1, Heat-treatable steels, alloy steels and free-cutting steels — Part 1: Non-alloy steels fo r quenching and tempehngISO 3744, Acoustics — Determination o f sound power levels and sound energy levels o f noise sources using sound pressure — Engineering methods fo r an essentially fre e field over a reflecting plane
ISO 3746:2010, Acoustics — Determination of sound power levels and sound energy levels o f noise sources using sound pressure — Survey method using an enveloping measurement surface over a reflecting plane
ISO 4413, Hydraulic flu id power — General rules and safety requirements fo r system s and their components
ISO 4414, Pneumaticfluid power — General rules and safety requirements fo r system s and their components
ISO 4871, Acoustics — Declaration and verification o f noise emission values o f machinery and equipment
ISO 9355-1, Ergonomic requirements fo r the design o f displays and control actuators — Part 1: Human interactions with displays and control actuators
ISO 9355-2, Ergonomic requirements fo r the design o f displays and control actuators — Part 2: Displays
ISO 9355-3, Ergonomic requirements fo r the design o f displays and control actuators — Part 3: Control actuators
ISO 9614-1, Acoustics — Determination o f sound power levels o f noise sources using sound intensity —
Part 1: Measurement at discrete points
ISO 11202:2010, Acoustics — Noise emitted by machinery and equipment — Determination o f emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
ISO 11204:2010, Acoustics — Noise emitted by machinery and equipment — Determination o f emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
ISO 12100:2010, Safety o f machinery — General principles fo r design — Risk assessment and risk reduction
ISO 13849-1:2015, Safety o f machinery — Safety-related parts o f control systems — Part 1: General principles for design
ISO 13850, Safety o f machinery — Emergency stop function — Principles for design
ISO 13854, Safety o f machinery — Minimum gaps to avoid crushing of parts of the human body
ISO 13855:2010, Safety o f machinery — Positioning o f safeguards with respect to the approach speeds of parts o f the human body
ISO 13856-1, Safety o f machinery — Pressure-sensitive protective devices — Part 1: General principles for design and testing o f pressure-sensitive mats and pressure-sensitive floors
ISO 13857:2008, Safety o f machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs
ISO 14119:2013, Safety o f machinery — Interlocking devices associated with guards — Principles for design and selection
ISO 14120:2015, Safety o f machinery — Guards — General requirements fo r the design and construction of fixed and movable guards
ISO 14122-2, Safety o f machinery — Permanent means o f access to machinery — Part 2: Working platforms and walkways
ISO 14122-3, Safety o f machinery — Permanent means o f access to machinery — Part 3: Stairs, stepiadders and guard-rails
ISO/TR 11688-1, Acoustics — Recommended practice fo r the design o f low-noise machinery and equipment — Part 1: Planning
IEC 60204-1:2009, Safety o f machinery — Electrical equipment o f machines — Part 1: General requirements
IEC 61000-6-2, Electromagnetic compatibility (EMC) — Part 6-2: Generic standards — immunity for industrial environments
IEC 61000-6-4, Electromagnetic compatibility (EMC) — Part 6-4: Generic standards — Emission standard fo r industrial environments
EN 1037:1995+A1:2008, Safety o f machinery — Prevention o f unexpected start-up
EN 1837:1999+A1:2009, Safety o f machinery — Integral lighting o f machines
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 12100, ISO 13849-1 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http electropedia.org
— ISO Online browsing platform: available at http iso.org/obp
3.1
sawing machine
machine tool that is used for cutting material and cutting into length using a sawing tool (3.9)
3.1.1
band-sawing machine
sawing machine (3.1) that is m ainly used for cutting material and cutting into length using a sawing tool
(3.9) which is designed as an flexible endless saw band
Note 1 to entry: Examples are given in Clause 5 and Figures 1 to fi.
3.1.2
circular sawing machine
sawing machine (3.1) for cutting bar and profile material to length w ith a sawing tool (3.9) which is
designed as a circular saw blade
Note 1 to entry: Examples are given in Clause 5. Figures 9 to 16 and Annex C.
3.1.3
hack-sawing machine
sawing machine (3.1) for cutting bar and profile material to length w ith a sawing tool (3.9) which is
clamped between the ends of a downwardly open bow
Note 1 to entry: Examples are given in Clause 5 and Figure 17.
3.1.4
automatic sawing machine
sawing machine (3.1) in which the power-operated elements perform continuous or repeat cycles
Note 1 to entry: The first cycle initiated by a control system starts from the operator until either an automatically
determined condition is achieved, or a stop signal is given by the operator.
Note 2 to entry: A typical cycle can be feeding of work material (3.13). clamping of work material, feeding of
sawing tool (3.9) through work material, sawing tool retraction, unclamping of workpiece (3.14). unloading of
workpiece and unclamping of work material. Repeat the above cycle until a stop signal is actuated.
3.2
back jaw feed
power-operated work material (3.13) feeding device having a carriage-mounted vice which grips the
work material at any point along its length and traverses it to the sawing position
3.3
load/unload position
zone of the machine where provision exists for manual loading onto, or unloading work m aterials)
(3.13) from the machine
Note 1 to entry: Frequent, but not continuous access, is required of operators during normal operation of the
machine.
3.4
manual sawing process
operation of the machine under manual control, all process steps in the machining sequence being
started or manually controlled by the operator
3.5
metalworking fluid
-----------------------------------------------------------
Данний документ, придатний для використання і в повному об'ємі знаходиться в ІДС "Зодчий"
Детальніше про Інформаційно-Довідкову Систему "Зодчий"
Інформаційно-довідкова система (ІДС) «ЗОДЧИЙ» - це база даних нормативно-правових документів у галузі будівництва, створена у відповідності до замовлень Міністерства архітектури України № 29 від 15.02.1994р. і № 43 від 09.03.1994 р. Це найпопулярніший на сьогодні ліцензійний збірник будівельних детальних документів України (зі змінами та доповненнями).
Базові будівельні нормативні документи ІДС "Зодчий" визнані всіма офіційними органи, мають силу печатних офіційних видань БНіП (СНИП), ГОСТ, ДБН, ДСТУ, ВБН (ВСН), ДНАОП, при цьому доступні за ціною та зручніші в зберіганні та використанні.