Державне підприємство «Український науково-дослідний і навчальний центр проблем стандартизації, сертифікації та якості» (ДП «УкрНДНЦ»)

Наказ від 23.10.2018 № 378

EN ISO 3040:2016
Geometrical product specifications (GPS) — Dimensioning and tolerancing — Cones (ISO 3040:2016)

прийнято як національний стандарт методом підтвердження за позначенням

ДСТУ EN ISO 3040:2018
(EN ISO 3040:2016, IDT; ISO 3040:2016, IDT)
Технічні вимоги до геометричних характеристик продукції (GPS). Конуси. Розміри та допуски

English Version

Geometrical product specifications (GPS) — Dimensioning
and tolerancing — Cones

1 Scope 

This International Standard specifies graphical indication applicable to a cone (right-angle circular
cones) to define its dimensioning or to specify its tolerancing.

For the purposes of this International Standard, the term “cone” relates to right-angle circular cones
only (any intersection by a plane perpendicular to the axis of the nominal cone is a circle).

NOTE 1 For simplicity, only truncated cones have been represented in this International Standard. However,
this International Standard can be applied to any type of cone within its scope.

NOTE 2 This International Standard is not intended to prevent the use of other methods of dimensioning and
tolerancing.

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

ISO 1119:2011, Geometrical product specifications (GPS) — Series of conical tapers and taper angles

ISO 81714-1, Design of graphical symbols for use in the technical documentation of products — Part 1:
Basic rules

3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.

3.1
rate of taper
 
C
ratio of the difference in the diameters of two sections of a cone to the distance between them
Note 1 to entry: lt is expressed by the following formula (see also Figure 1).

--------------------------------------

Данний документ, придатний для використання і в повному об'ємі знаходиться в ІДС "Зодчий"

Детальніше про Інформаційно-Довідкову Систему "Зодчий"

Інформаційно-довідкова система (ІДС) «ЗОДЧИЙ» - це база даних нормативно-правових документів у галузі будівництва, створена у відповідності до замовлень Міністерства архітектури України № 29 від 15.02.1994р. і № 43 від 09.03.1994 р. Це найпопулярніший на сьогодні ліцензійний збірник будівельних детальних документів України (зі змінами та доповненнями).
Базові будівельні нормативні документи ІДС "Зодчий" визнані всіма офіційними органи, мають силу печатних офіційних видань БНіП (СНИП), ГОСТ, ДБН, ДСТУ, ВБН (ВСН), ДНАОП, при цьому доступні за ціною та зручніші в зберіганні та використанні.

 Ліцензійні програми за ціною виробника

 Для автоматизації визначення вартості будівництва - нового, реконструкції, капітального ремонту та технічного переоснащення Повний набір діючих в Україні будівельних нормативних документів та актів в останній редакції Нормативи і інструменти для впровадження та розрахунку всієї кошторисної і підрядної документації